CELASCHI TSA 360

Copyright @ All Rights Reserved

Bank

2

"CELASCHI" mod. TSA 320 DS - AUTOMATIC DOUBLE END TENONER

Email: info@euroteckitalia.com

EUROTECK ITALIA

WOODWORKING MACHINES

AUTOMATIC DOUBLE END TENONER CELASCHI TSA 320 DS

with 4 +4 spindles

 

High performance machine.

Heavy-duty structure in welded and stress-released steel, dimensioned according to machine-configuration and length.

Fixed left Hand side – Right hand side movable along double

ground steel guides, with automatic lubrication.

Positioning control also possible with remote control board.

Safety relay to prevent start of the movable side while

chain-track is running and to prevent the track from running

while the movable side is being positioned.

The joining pins, in hardened-steel,16-mm diameter, run on

dust sealed- and life lubricated bearings .

Pop up dogs at every 400 mm distance

Chain-track covering pads are made in high resistance vulcanized rubber on steel plates.

The steel support plate is 2mm thick and is attached to the top of the chain-link by 4 screws.

The balanced transmission shaft (diameter 80-mm) has a large-size positive keyway and driving sprocket

The sprockets are hardened in the contact points.

Top pressure beams have a single powered V-belt with clutch.

Infeeding and outfeed steel covers for chain protection.

The columns which hold the working units and saddle/slide supports

are made in solid cast-iron with precision ground dovetail guides.

Centralized lubrication system for all sliding surfaces of the saddle-slide.

Electrical cabinet supplied with standard 3 m connecting cables.

Emergency stop cable at back, thickness safety on top

Pressure beams and stop press button on control cabinet.

Safety Photocells at front

 

TECHNCAL DATA ;

- WORKING WIDTH MM 220 – 3,000

- WORKPIECE THICKNESS MM 8-80

- USEFULL SPACE IN ENTRY : 1000 mm

- TOP PRESSURE BEAMS WITH DRIVE BELTS AND CLUTCH

- BOTTOM FEED CHAINS MM 80 WIDTH WITH BEARINGS

- AUTOMATIC LUBRICATION OF BEDPLATES

- AUTOMATIC LUBRICATION OF FEED CHAINS

- AUTOMATIC IN-OUT POP UP DOGS DISTANCE 400 MM

- VARIABLE FEED SPEED 4-24 MT/MIN

- ELECTRONIC OPENING OF MOVABLE SIDE BY 2-SPEED MOTOR

(FAST/SLOW)

- ELETTRONIC MOTORIZZED LIFTING OF TOP PRESSURE BEAMS

- MANUALS AND ELECTRIC DIAGRAMS

- SEPARATE CONTROL CABINET

- VOLTS 380V/3ph/50 hertz

 

MACHINE EQUIPPED WITH :

 

- LH ADJUSTABLE INFEED SIDE FENCE- MANUAL HORIZONTAL ADJUSTMENT

 

1-2 JUMP CUTTING/SCORING UNIT attached to the Hogging units

- MOTORS 1,6 KW (2.2HP) – 6000 RPM BY INVERTER

- shafts diam 25 X 28 L - max tool diam 150

 

3-4 HOGGING/MILLING UNIT - 5.5/8 HP - 6000 RPM

- SHAFTS DIA 35x62 - Max tool diam 250mm

- DUST OUTLET DIAM 140mm

- TILTABLE 0-90 DEGREES

- manual vertical/horizontal adjustment with digital readout

 

5-6 JUMP MILLING UNIT - 5.5/8 HP - 6000 RPM

- WITH PNEUMATIC JUMP IN/OUT

- HEAVY DUTY MOTORS

- TILTABLE 0-90 DEGREES

- manual vertical/horizontal adjustment with digital readout

- SHAFTS DIA 35 x 62 - Max tool dia 250mm

-DUST OUTLET DIA 120mm

 

7-8 MILLING UNIT 5.5/8 HP - 6000 RPM

TILTABLE 0-90 DEGREES

- manual vertical/horizontal adjustment with digital readout

- SHAFTS DIA 35 x 62 - Max tool dia 250mm

-DUST OUTLET DIA 120mm

 

- MOTORS DRIVEN BY STATIC INVERTER

- MAIN DRIVE MOTOR - SPEED ADJUSTABLE BY INVERTER

- ELECTRONIC HEIGHT ADJUSTMENT (THICKNESS), PROGRAMMABLE

- ELECTRONIC WIDTH ADJUSTMENT, PROGRAMMABLE

- DUST AND SOUNDPROOF CABINETS

 

MACHINE IN VERY GOOD CONDITIONS